Grounding Coaxial Cable Shields: Why, Where, & How?

grounding-coaxial-cable-shields

Even today it’s a controversial subject – but we don’t know why. The purpose and importance of grounding coaxial line shields are so critical to safe and clean telecommunication station operation that it should not be a matter of discussion, except as a how-to subject such as this paper represents.

The coaxial cable used in radio and television work is referred to as an unbalanced line primarily because the center conductor carries the current and signal voltage nearly all to itself.

The shield of the transmission line is just that – a shield. It carries no current except for a small induced current flowing as the result of induction by length. In a perfectly matched system, the current in the shield is almost nil.

That’s also why in most modern applications coaxial cable shields are fitted to connectors without soldering – only compression fitting. Center conductors carry the current during transmission so they are generally soldered in place.

But that doesn’t mean that the shield has no work to do, and that’s the purpose of this brief technical narrative. Coaxial shields provide protection for the center conductor and prevent ground-level line leakage during transmission, noise pickup from external local sources during the reception, continuous impedance matching, and physical rigidity to the line.

Short distance grounding of coaxial shields introduces earthen neutral integrity to the shield and provides a drain-source for the very types of disturbances the shield is designed to resist.

It’s very common to hear of stories relating to how interference to other services disappeared or reception noise was reduced when shield grounding was accomplished.

In lightning protection applications the shield is an exposed element, and when lightning strikes overhead or a direct “hit’ occurs to antennas and tower frames it’s not unusual to find as much as 80% of the applied current seeking ground through the transmission line flows down the shield.

If the lightning currents do not find earth through a dissipation point before reaching the radio equipment chassis then damage to the station gear will nearly always result. In severe cases, injury or loss of structure can occur. Grounding of shields is easy and requires little experience or effort.

The connections for grounding should always be done at ground level if the maximum value is to be obtained, and the lead length from the shield to earth entry point (the dirt) should be kept as short as possible – less than a foot if possible.

Using a commercial grounding block is a very neat way of accomplishing the task, but making your own shield connections can be done as well.

Cutting the cable, inserting connectors, and grounding the shield by attachment to the connectors is a common method but suffers from the inevitable impedance “bump” in the line at that point and the possibility of exposure to water or contaminants.

Removing the outer plastic with a sharp knife carefully, wrapping a solid copper wire around the exposed shield, and then grounding the wire is another method that seems to work well and doesn’t leave an impedance irregularity in the line.

However, the work done is far less important than making sure it gets done, and establishing a common point for multiple shield grounding makes sense in stations that use many different transmission lines.

But the most important element is to be sure that the coaxial cable lines are ALWAYS brought to the ground surface first and that shield grounding is accomplished at that point BEFORE the cable continues on its way to reach station equipment.

Why is the grounding of coaxial cable shields important?

Grounding coaxial cable shields, especially in low-level circuits, is essential for protection against externally induced noise. The integrity of the connection to the ground is vital, as a poor ground might be more detrimental than having no ground at all.

What role does the shield serve in coaxial cables?

In coaxial cables, the shield is used as a signal return path. It serves a dual purpose: screening the center conductor from external fields and acting as a protective barrier against noise and interference. The shield’s resistance is typically much lower than other conductors, making it crucial for presenting a low impedance against external induction.

How does grounding help in the case of electromagnetic interference (EMI)?

A grounded shield acts as a conductive channel for the conductor(s) within. Anchored at ground potential, the shield divides an offending electric field and directs part of it into the ground. This method serves more as a means of dividing the noise rather than walling it off.

What is a ground loop, and how does it impact noise?

Ground loops can cause significant noise. They occur when more than one circuit shares the same return conductor, often a shield intended to be the ground. This can result in voltage drops from one current path appearing in another, introducing unwanted noise into the signal. Ground loops are best eliminated with a thoughtful installation, and common grounds are ideally run in a star configuration.

How should the outer conductive shield of a coaxial cable be grounded when entering a building?

When the coaxial cable enters a building, the outer conductive shield should be grounded as close as practicable to the point of entrance in accordance with specific grounding standards.

Keep the connections clean, tight, and waterproof – then relax and enjoy the benefits of your efforts!